Acid Injector

Size 2.1mm
Gallons Per Minute 3-4
Inlet 3/8" MPT
Outlet 3/8" MPT
PSI 3000
Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode.
Draw rate 0 to 20%, Ceramic ball for injecting acids
1/4" Hose Barb Chemical Port
Minimum 35% pressure drop for draw
Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less

Equipment Type Pressure Washer
PSI 3000
Inlet 1/4" Port
Size 2.3mm
Gallons Per Minute 5-8
One piece quick connect injectors. Nickel plated for acid injection
Downstream injector ready to install on your system
Chemical draw up to 20%
Kit includes injector with quick connect plug on inlet and quick connect socket on outlet of the injector, 4 ft of clear vinyl tubing and a strainer.
Temperature 190° F

Size 1.8mm
Gallons Per Minute 2-3
Temperature 194°F
Inlet 3/8" MPT
Outlet 3/8" MPT
PSI 3000
Draw rate 0 to 20%, Ceramic ball for injecting acids
Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode.
Minimum 35% pressure drop for draw
1/4" Hose Barb Chemical Port
Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less

Equipment Type Pressure Washer
Orifice 2.1mm
Gallons Per Minute 3-4
Quick Connect Plug Inlet, Quick Connect Socket Outlet
4 Feet Clear Vinyl Tubing
Strainer With Check Valve
Downstream injector ready to install on your system.
Kit includes injector with quick connect plug on inlet and quick connect socket on outlet of the injector, 4 ft of clear vinyl tubing and a strainer.

Equipment Type Pressure Washer
Up to 20% injestion Draw Rate
Temperature 190° F
Inlet 3/8" MPT
Outlet 3/8" MPT
1/4" Hose Barb Chemical Port
Made In The U.S.A
Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode.
Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less
PSI 4500

Gallons Per Minute Adjustable 2 to 8 gpm injection ratio approx. 10 to 1
PSI 3600
Temperature 194° F
1/4" hose barb
Equipment Type Pressure Washer
Outlet 3/8" FPT
Inlet 3/8" FPT

Size 2.3mm
Gallons Per Minute 4-5
Inlet 3/8" MPT
Outlet 3/8" MPT
PSI 3000
Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode.
Draw rate 0 to 20%, Ceramic ball for injecting acids
Minimum 35% pressure drop for draw
1/4" Hose Barb Chemical Port
Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less
Temperature 194° F

Equipment Type Pressure Washer
Includes 2 springs, 2 o-rings, Ceramic ball
Fits All GPM Flow Rates

Equipment Type Pressure Washer
Orifice 1.8mm
Quick Connect Plug Inlet, Quick Connect Socket Outlet
4 Feet Clear Vinyl Tubing
Strainer With Check Valve
Gallons Per Minute 2-3
Downstream injector ready to install on your system.
Kit includes injector with quick connect plug on inlet and quick connect socket on outlet of the injector, 4 ft of clear vinyl tubing and a strainer.

Equipment Type Pressure Washer
Orifice 2.3mm
Gallons Per Minute 4-5
Quick Connect Plug Inlet, Quick Connect Socket Outlet
4 Feet Clear Vinyl Tubing
Strainer With Check Valve
Downstream injector ready to install on your system.
Kit includes injector with quick connect plug on inlet and quick connect socket on outlet of the injector, 4 ft of clear vinyl tubing and a strainer.