Rotating Nozzle Kit

Equipment Type Pressure Washer
Temperature 212°F
PSI 3700
Inlet 1/4"
Nozzle Size 6.0
Includes Ceramic Tip, Rotor, and O-Ring
It is recommended to use a high pressure filter to prevent internal damage from water minerals. Rotating nozzle increase cleaning ability with the impact of a 0 wide angle spray coverage. The Roto-Jet produces up to 3000 PSI of cleaning power to handle almost any high pressure spraying application.
Note: START THIS NOZZLE IN THE DOWN POSITION TO PREVENT CERAMIC DAMAGE

Color Black
Inlet 1/4"
Rotating Nozzles are designed to clean with the impact of zero degree flat spray nozzles but with the pattern of a 25 degree nozzle. Rotating nozzles will cut your cleaning time in half. With a rotating nozzle, you can clean the following quickly; rust removal, tank cleaning, paint and graffiti removal, brick cleaning, concrete, gum from sidewalks, boat cleaning and barnacle removal, asbestos abatement, cleaning crab and lobster pots, fish nets, and removing mud and clay from highway equipment. Spins Faster than IDK nozzle, No lines or streaking, Used for cleaning
Nozzle Size 5.5
Note: All rotating nozzles MUST be started with the nozzle pointing to the ground. This prevents damage to the ceramic orifice. It is highly recommended that a high pressure filter be used with each nozzle. Not using a filter could void any warranty. Eye protection must be worn while using these nozzles.
Note: Must be started with nozzle pointed to ground
Temperature 180° F
PSI 3200

Equipment Type Pressure Washer

Equipment Type Pressure Washer
Note: Fits All Rotomax Rotating Nozzles

Equipment Type Pressure Washer
Temperature 212°F
PSI 4500
Inlet 1/4"
Nozzle Size 4.0
Includes Ceramic Tip, Rotor, and O-Ring
It is recommended to use a high pressure filter to prevent internal damage from water minerals. Rotating nozzle increase cleaning ability with the impact of a 0 wide angle spray coverage. The Roto-Jet produces up to 3000 PSI of cleaning power to handle almost any high pressure spraying application.
Note: START THIS NOZZLE IN THE DOWN POSITION TO PREVENT CERAMIC DAMAGE

Color White
Inlet 1/4"
Rotating Nozzles are designed to clean with the impact of zero degree flat spray nozzles but with the pattern of a 25 degree nozzle. Rotating nozzles will cut your cleaning time in half. With a rotating nozzle, you can clean the following quickly; rust removal, tank cleaning, paint and graffiti removal, brick cleaning, concrete, gum from sidewalks, boat cleaning and barnacle removal, asbestos abatement, cleaning crab and lobster pots, fish nets, and removing mud and clay from highway equipment. Spins Faster than IDK nozzle, No lines or streaking, Used for cleaning
Nozzle Size 3.5
Note: Must be started with nozzle pointed to ground
Note: All rotating nozzles MUST be started with the nozzle pointing to the ground. This prevents damage to the ceramic orifice. It is highly recommended that a high pressure filter be used with each nozzle. Not using a filter could void any warranty. Eye protection must be worn while using these nozzles.
PSI 3200
Temperature 180° F

Color Yellow
Inlet 1/4"
Rotating Nozzles are designed to clean with the impact of zero degree flat spray nozzles but with the pattern of a 25 degree nozzle. Rotating nozzles will cut your cleaning time in half. With a rotating nozzle, you can clean the following quickly; rust removal, tank cleaning, paint and graffiti removal, brick cleaning, concrete, gum from sidewalks, boat cleaning and barnacle removal, asbestos abatement, cleaning crab and lobster pots, fish nets, and removing mud and clay from highway equipment. Spins Faster than IDK nozzle, No lines or streaking, Used for cleaning
Nozzle Size 4.5
Note: Must be started with nozzle pointed to ground
Note: All rotating nozzles MUST be started with the nozzle pointing to the ground. This prevents damage to the ceramic orifice. It is highly recommended that a high pressure filter be used with each nozzle. Not using a filter could void any warranty. Eye protection must be worn while using these nozzles
Temperature 180° F
PSI 3200

Color Red
Inlet 1/4" FPT
Nozzle Size 8.0
Blast dirt, grime, slime, mold, mildew, etc. off instantly using the Dirt Killer nozzle. Save chemical, water, time, and money. The Dirt Killer generates a whirl wind of water droplets so powerful the imbedded dirt is blown away. Dirt Killer nozzles, which feature a rotating turbine, deliver the punch of a zero degree nozzle with a 25 degree fan, creating 10 times the cleaning impact of a standard flat tip nozzle. Industrial Dirt Killer is the world's most powerful cleaning nozzle. It also features a spinning head, which moves at a much slower speed to produce large water droplets that deliver a devastating blasting force. The IDK has the ability to attack and thoroughly clean 3-dimensional surfaces such as concrete and steel. Difficult cleaning projects, such as crab pots, hog confinements, farrowing crates, milk barns, and many others, are made easy with this incredible tool.
By using properly, the Dirt Killer will perform as follows: at 3000 PSI aproximately 250 to 400 hours: at 2000 PSI approximately 300 to 500 hours: at 1000 PSI approximatley 400 to 700 hours before rebuilding or replacing
REBUILDING INSTRUCTIONS: (1) Remove cover and unscrew inlet adapter. (2) Remove turbine nozzle and check for clogs. (3) If clogged, clear turbine nozzle re-assemble. (4) To rebuild entire nozzle remove entire contents, to include seat. (5) Put small o-ring on tip of seat with loctite and press seat into tip of nozzle. (6) Change large o-ring on inlet adapter. (7). Drop turbine nozzle into nozzle body and screw inlet adapter on. Back of nozzle turbine should NOT be centered. (8) Put cover back on Dirt Killer
SERVICE ADVISORY: Using a high pressure filter increases the life of the IDK nozzle. When using with hot water, it is strongly recommended you use the filter and lubricate the nozzle every 2 to 3 hours with a teflon blended oil. Do not touch rotating water pattern. ALWAYS START WITH THE NOZZLE POINTING TOWARDS THE GROUND.
Temperature 200° F
PSI 4700

Color Black
Inlet 1/4" FPT
Nozzle Size 5.5
Blast dirt, grime, slime, mold, mildew, etc. off instantly using the Dirt Killer nozzle. Save chemical, water, time, and money. The Dirt Killer generates a whirl wind of water droplets so powerful the imbedded dirt is blown away. Dirt Killer nozzles, which feature a rotating turbine, deliver the punch of a zero degree nozzle with a 25 degree fan, creating 10 times the cleaning impact of a standard flat tip nozzle. Industrial Dirt Killer is the world's most powerful cleaning nozzle. It also features a spinning head, which moves at a much slower speed to produce large water droplets that deliver a devastating blasting force. The IDK has the ability to attack and thoroughly clean 3-dimensional surfaces such as concrete and steel. Difficult cleaning projects, such as crab pots, hog confinements, farrowing crates, milk barns, and many others, are made easy with this incredible tool.
By using properly, the Dirt Killer will perform as follows: at 3000 PSI aproximately 250 to 400 hours: at 2000 PSI approximately 300 to 500 hours: at 1000 PSI approximatley 400 to 700 hours before rebuilding or replacing.
REBUILDING INSTRUCTIONS: (1) Remove cover and unscrew inlet adapter. (2) Remove turbine nozzle and check for clogs. (3) If clogged, clear turbine nozzle re-assemble. (4) To rebuild entire nozzle remove entire contents, to include seat. (5) Put small o-ring on tip of seat with loctite and press seat into tip of nozzle. (6) Change large o-ring on inlet adapter. (7). Drop turbine nozzle into nozzle body and screw inlet adapter on. Back of nozzle turbine should NOT be centered. (8) Put cover back on Dirt Killer
SERVICE ADVISORY: Using a high pressure filter increases the life of the IDK nozzle. When using with hot water, it is strongly recommended you use the filter and lubricate the nozzle every 2 to 3 hours with a teflon blended oil. Do not touch rotating water pattern. ALWAYS START WITH THE NOZZLE POINTING TOWARDS THE GROUND
PSI 4700
Temperature 200° F

Inlet 1/4" FPT
Spins slower than DK nozzle, Produces greater impact, For water blasting, Heavy duty cleaning.
Nozzle Size 4.5
Color Green
Blast dirt, grime, slime, mold, mildew, etc. off instantly using the Dirt Killer nozzle. Save chemical, water, time, and money. The Dirt Killer generates a whirl wind of water droplets so powerful the imbedded dirt is blown away. Dirt Killer nozzles, which feature a rotating turbine, deliver the punch of a zero degree nozzle with a 25 degree fan, creating 10 times the cleaning impact of a standard flat tip nozzle. Industrial Dirt Killer is the world's most powerful cleaning nozzle. It also features a spinning head, which moves at a much slower speed to produce large water droplets that deliver a devastating blasting force. The IDK has the ability to attack and thoroughly clean 3-dimensional surfaces such as concrete and steel. Difficult cleaning projects, such as crab pots, hog confinements, farrowing crates, milk barns, and many others, are made easy with this incredible tool.
By using properly, the Dirt Killer will perform as follows: at 3000 PSI aproximately 250 to 400 hours: at 2000 PSI approximately 300 to 500 hours: at 1000 PSI approximatley 400 to 700 hours before rebuilding or replacing.
REBUILDING INSTRUCTIONS: (1) Remove cover and unscrew inlet adapter. (2) Remove turbine nozzle and check for clogs. (3) If clogged, clear turbine nozzle re-assemble. (4) To rebuild entire nozzle remove entire contents, to include seat. (5) Put small o-ring on tip of seat with loctite and press seat into tip of nozzle. (6) Change large o-ring on inlet adapter. (7). Drop turbine nozzle into nozzle body and screw inlet adapter on. Back of nozzle turbine should NOT be centered. (8) Put cover back on Dirt Killer
SERVICE ADVISORY: Using a high pressure filter increases the life of the IDK nozzle. When using with hot water, it is strongly recommended you use the filter and lubricate the nozzle every 2 to 3 hours with a teflon blended oil. Do not touch rotating water pattern. ALWAYS START WITH THE NOZZLE POINTING TOWARDS THE GROUND.
Note: Must be started with nozzle pointed to ground
Temperature 200° F
PSI 4700