Do It Yourself Section My Garage Section Parts Look Up

Over 1,000,000 Orders Shipped Since 1997!


Pressure Washer Injector

Pressure Washer Injector: Jack’s is your place! We have the Pressure Washer Injector you need, with fast shipping and great prices. For Pressure Washer parts and accessories, think Jack’s!

Popular Pressure Washer Injector  

 


1.8mm GP High Draw Adjustable Acid Injector

Part Number: 5786
 
Specs
Temperature: 190° F
Inlet: 3/8" MPT
Outlet: 3/8" MPT
Equipment Type: Pressure Washer
PSI: 4500

Up to 20% injestion Draw Rate 1/4" Hose Barb Chemical Port Made In The U.S.A Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode. Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less
Fits Model

Replaces OEM
Universal : General Pump :
Your Price:
$24.28
 
No Sales Tax, except in MD
Qty:


ROBOKIM 190000 Chem Repair Kit

Part Number: 1270
 
Specs
Includes: 1 stainless steel spring, 1 stainless steel ball, 5 o-rings
Equipment Type: Pressure Washer


Fits Model

Replaces OEM
Universal : General Pump :
Your Price:
$7.75
 
No Sales Tax, except in MD
Qty:


Plastic Chemical Strainer with Check Valve

Part Number: 1285
 
Specs
Color: Black
Material: Plastic
Includes: Check Valve
Equipment Type: Pressure Washer


Fits Model

Replaces OEM
Universal :
Your Price:
$2.64
 
No Sales Tax, except in MD
Qty:


Brass Chemical Metering Valve

Part Number: 1296
 
Specs
Temperature: 300°F
Inlet: 1/4" FPT
Outlet: 1/4" FPT
Equipment Type: Pressure Washer
PSI: 4000

Connect to inlet line for chemical metering. Open knob clockwise to allow chemical to flow through pump.
Fits Model

Replaces OEM
Universal :
Your Price:
$27.91
 
No Sales Tax, except in MD
Qty:


ST 62 Adjustable Acid Injector

Part Number: 1719
 
Specs
Temperature: 194° F
Inlet: 3/8" FPT
Gallons Per Minute: Adjustable 2 to 8 gpm injection ratio approx. 10 to 1
Outlet: 3/8" FPT
Equipment Type: Pressure Washer
PSI: 3600

1/4" hose barb
Fits Model

Replaces OEM
Universal : Suttner :
Your Price:
$38.32
 
No Sales Tax, except in MD
Qty:


ST 61 Metering Valve

Part Number: 1956
 
Specs
Equipment Type: Pressure Washer

connects to the chemical inlet barb without special tools. Made of a glass filled poly material, it is extremely corrosion resistant
Fits Model

Replaces OEM
Universal : Suttner :
Your Price:
$18.58
 
No Sales Tax, except in MD
Qty:


1.8mm Adjustable Acid Injector

Part Number: 1958
 
Specs
Temperature: 194°F
Inlet: 3/8" MPT
Size: 1.8mm
Gallons Per Minute: 2-3
Outlet: 3/8" MPT
PSI: 3000

Draw rate 0 to 20%, Ceramic ball for injecting acids Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode. Minimum 35% pressure drop for draw 1/4" Hose Barb Chemical Port Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less
Fits Model

Replaces OEM
Universal : JE Adams :
Your Price:
$35.42
 
No Sales Tax, except in MD
Qty:


2.1mm Adjustable Acid Injector

Part Number: 1959
 
Specs
Inlet: 3/8" MPT
Size: 2.1mm
Gallons Per Minute: 3-4
Outlet: 3/8" MPT
PSI: 3000

Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode. Draw rate 0 to 20%, Ceramic ball for injecting acids 1/4" Hose Barb Chemical Port Minimum 35% pressure drop for draw Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less
Fits Model

Replaces OEM
Universal : JE Adams :
Your Price:
$35.42
 
No Sales Tax, except in MD
Qty:


2.3mm Adjustable Acid Injector

Part Number: 1960
 
Specs
Temperature: 194° F
Inlet: 3/8" MPT
Size: 2.3mm
Gallons Per Minute: 4-5
Outlet: 3/8" MPT
PSI: 3000

Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode. Draw rate 0 to 20%, Ceramic ball for injecting acids Minimum 35% pressure drop for draw 1/4" Hose Barb Chemical Port Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less
Fits Model

Replaces OEM
Universal : JE Adams :
Your Price:
$35.42
 
No Sales Tax, except in MD
Qty:


Pressure Washer Injector Repair Kit

Part Number: 1966
 
Specs
Includes: 1 spring, 2 o-rings, ceramic ball
Equipment Type: Pressure Washer

Fits All GPM Flow Rates
Fits Model

Replaces OEM
Universal : General Pump : JE Adams :
Your Price:
$7.05
 
No Sales Tax, except in MD
Qty:


ROBOKIM #0 Adjustable Chemical Injector

Part Number: 2041
 
Specs
Temperature: 210° F Maximum
Inlet: 3/8"mpt
Gallons Per Minute: 2.1-2.9
Spec: 1.0" x 2.7" x3.1"
Outlet: 3/8"mpt
Material: Brass
Weight: .6 lb
Equipment Type: Pressure Washer
PSI: 3200

Will draw between 125 & 250 PSI only Refer to the arrow on the injector body for proper flow direction. Install the injector in the system downstream of the regulator unloader which is downstream of the pump. These injectors will draw your chemical into the water stream at 125 PSI and 2.1 to 10.8 GPM, through your low pressure nozzle. Injector WILL NOT draw chemical above 250 PSI through your high pressure nozzle. The amount of chemical drawn in is controlled with the adjustment knob. Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode. Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less
Fits Model

Replaces OEM
Universal : General Pump :
Your Price:
$40.11
 
No Sales Tax, except in MD
Qty:


ROBOKIM #1 Adjustable Chemical Injector

Part Number: 2042
 
Specs
Temperature: 210° F Maximum
Inlet: 3/8"mpt
Gallons Per Minute: 2.9 - 4.0
Spec: 1.0" x 2.7" x3.1"
Outlet: 3/8"mpt
Material: Brass
Weight: .6 lb
Equipment Type: Pressure Washer
PSI: 3200

Will draw between 125 & 250 PSI only Refer to the arrow on the injector body for proper flow direction. Install the injector in the system downstream of the regulator unloader which is downstream of the pump. These injectors will draw your chemical into the water stream at 125 PSI and 2.1 to 10.8 GPM, through your low pressure nozzle. Injector WILL NOT draw chemical above 250 PSI through your high pressure nozzle. The amount of chemical drawn in is controlled with the adjustment knob. Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode. Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less
Fits Model

Replaces OEM
Universal : General Pump :
Your Price:
$40.11
 
No Sales Tax, except in MD
Qty:


ROBOKIM #2 Adjustable Chemical Injector

Part Number: 2043
 
Specs
Temperature: 210° F Maximum
Inlet: 3/8"mpt
Gallons Per Minute: 4.0 - 5.6
Spec: 1.0" x 2.7" x3.1"
Outlet: 3/8"mpt
Material: Brass
Weight: .6lb
Equipment Type: Pressure Washer
PSI: 3200

Will draw between 125 & 250 PSI only Refer to the arrow on the injector body for proper flow direction. Install the injector in the system downstream of the regulator unloader which is downstream of the pump. These injectors will draw your chemical into the water stream at 125 PSI and 2.1 to 10.8 GPM, through your low pressure nozzle. Injector WILL NOT draw chemical above 250 PSI through your high pressure nozzle. The amount of chemical drawn in is controlled with the adjustment knob. Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode. Note: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less
Fits Model

Replaces OEM
Universal : General Pump :
Your Price:
$40.11
 
No Sales Tax, except in MD
Qty:


ROBOKIM #3 Adjustable Chemical Injector

Part Number: 2044
 
Specs
Note:: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less.
Temperature: 210° F Maximum
Inlet: 3/8"mpt
Gallons Per Minute: 5.6 - 10.8
Spec: 1.0" x 2.7" x3.1"
Outlet: 3/8"mpt
Material: Brass
Equipment Type: Pressure Washer
PSI: 3200

Will draw between 125 & 250 PSI only Refer to the arrow on the injector body for proper flow direction. Install the injector in the system downstream of the regulator unloader which is downstream of the pump. These injectors will draw your chemical into the water stream at 125 PSI and 2.1 to 10.8 GPM, through your low pressure nozzle. Injector WILL NOT draw chemical above 250 PSI through your high pressure nozzle. The amount of chemical drawn in is controlled with the adjustment knob. Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode.
Fits Model

Replaces OEM
General Pump :
Your Price:
$40.11
 
No Sales Tax, except in MD
Qty:


Quick Connect 1.8mm Acid Injector

Part Number: 2178
 
Specs
Gallons Per Minute: 2-3
Orifice: 1.8mm
Equipment Type: Pressure Washer

Quick Connect Plug Inlet, Quick Connect Socket Outlet 4 Feet Clear Vinyl Tubing Strainer With Check Valve Downstream injector ready to install on your system. Kit includes injector with quick connect plug on inlet and quick connect socket on outlet of the injector, 4 ft of clear vinyl tubing and a strainer.
Fits Model

Replaces OEM
Universal : JE Adams :
Your Price:
$43.17
 
No Sales Tax, except in MD
Qty:


Quick Connect 2.1mm Acid Injector

Part Number: 2179
 
Specs
Gallons Per Minute: 3-4
Orifice: 2.1mm
Equipment Type: Pressure Washer

Quick Connect Plug Inlet, Quick Connect Socket Outlet 4 Feet Clear Vinyl Tubing Strainer With Check Valve Downstream injector ready to install on your system. Kit includes injector with quick connect plug on inlet and quick connect socket on outlet of the injector, 4 ft of clear vinyl tubing and a strainer.
Fits Model

Replaces OEM
Universal : JE Adams :
Your Price:
$43.17
 
No Sales Tax, except in MD
Qty:


Quick Connect 2.3mm Acid Injector

Part Number: 2180
 
Specs
Gallons Per Minute: 4-5
Orifice: 2.3mm
Equipment Type: Pressure Washer

Quick Connect Plug Inlet, Quick Connect Socket Outlet 4 Feet Clear Vinyl Tubing Strainer With Check Valve Downstream injector ready to install on your system. Kit includes injector with quick connect plug on inlet and quick connect socket on outlet of the injector, 4 ft of clear vinyl tubing and a strainer.
Fits Model

Replaces OEM
Universal : JE Adams :
Your Price:
$43.17
 
No Sales Tax, except in MD
Qty:


ROBOKIM #0 Quick Connect Chemical Injector

Part Number: 2193
 
Specs
Inlet: 3/8" Plug
Gallons Per Minute: 2.1-2.9
Outlet: 3/8" Quick Change Socket
Equipment Type: Pressure Washer

Robokim injector kit comes complete with a 3/8" plug on the inlet, and a 3/8" quick change socket on the outlet. In addition, 6 feet of clear plastic tubing and a chemical strainer are included. A downstram injector for low pressure chemical applications. Features an adjustable metering knob. Use in conjunction with a double lance, adjustable nozzle, or other means of changing to low pressure while retaining system's output flow. Refer to the arrow on the injector body for porper flow direction. Install the injector in the system downstream of the regulator unloader which is downstream of the pump. These injectors will draw your chemical into the water stream at 125PSI and 2.1 to 10.8 GPM, through your low pressure nozzle. Injector WILL NOT draw chemical above 250 PSI through your high pressure nozzle. The amount of chemical drawn in is controlled with the adjustment knob. Maximum pressure: 3200 PSI. Maximum temperature: 210 degrees F. Inlet port: 3/8" MPT. Outlet port: 3/8" MPT. Dimensions: 1.0" x 2.7" x3.1". Weight: .6 lb. Repair Kit: (chemical) Barens order #1270. (acid) Barens #3846. 4 feet clear vinyl tubing Strainer with check valve
Fits Model

Replaces OEM
Universal : General Pump :
Your Price:
$51.81
 
No Sales Tax, except in MD
Qty:


ROBOKIM #1 Quick Connect Chemical Injector

Part Number: 2194
 
Specs
Inlet: 3/8" Plug
Gallons Per Minute: 2.9-4.0
Outlet: 3/8" Quick Change Socket
Equipment Type: Pressure Washer

Robokim injector kit comes complete with a 3/8" plug on the inlet, and a 3/8" quick change socket on the outlet. In addition, 6 feet of clear plastic tubing and a chemical strainer are included. A downstram injector for low pressure chemical applications. Features an adjustable metering knob. Use in conjunction with a double lance, adjustable nozzle, or other means of changing to low pressure while retaining system's output flow. Refer to the arrow on the injector body for porper flow direction. Install the injector in the system downstream of the regulator unloader which is downstream of the pump. These injectors will draw your chemical into the water stream at 125PSI and 2.1 to 10.8 GPM, through your low pressure nozzle. Injector WILL NOT draw chemical above 250 PSI through your high pressure nozzle. The amount of chemical drawn in is controlled with the adjustment knob. Maximum pressure: 3200 PSI. Maximum temperature: 210 degrees F. Inlet port: 3/8" MPT. Outlet port: 3/8" MPT. Dimensions: 1.0" x 2.7" x3.1". Weight: .6 lb. Repair Kit: (chemical) Barens order #1270. (acid) Barens #3846. 4 feet clear vinyl tubing Strainer with check valve
Fits Model

Replaces OEM
Universal : General Pump :
Your Price:
$51.81
 
No Sales Tax, except in MD
Qty:


ROBOKIM #2 Quick Connect Chemical Injector

Part Number: 2195
 
Specs
Inlet: 3/8" Plug
Gallons Per Minute: 4.0-5.6
Outlet: 3/8" Quick Change Socket
Equipment Type: Pressure Washer

Robokim injector kit comes complete with a 3/8" plug on the inlet, and a 3/8" quick change socket on the outlet. In addition, 6 feet of clear plastic tubing and a chemical strainer are included. A downstram injector for low pressure chemical applications. Features an adjustable metering knob. Use in conjunction with a double lance, adjustable nozzle, or other means of changing to low pressure while retaining system's output flow. Refer to the arrow on the injector body for porper flow direction. Install the injector in the system downstream of the regulator unloader which is downstream of the pump. These injectors will draw your chemical into the water stream at 125PSI and 2.1 to 10.8 GPM, through your low pressure nozzle. Injector WILL NOT draw chemical above 250 PSI through your high pressure nozzle. The amount of chemical drawn in is controlled with the adjustment knob. Maximum pressure: 3200 PSI. Maximum temperature: 210 degrees F. Inlet port: 3/8" MPT. Outlet port: 3/8" MPT. Dimensions: 1.0" x 2.7" x3.1". Weight: .6 lb. Repair Kit: (chemical) Barens order #1270. (acid) Barens #3846. 4 feet clear vinyl tubing Strainer with check valve
Fits Model

Replaces OEM
Universal : General Pump :
Your Price:
$51.81
 
No Sales Tax, except in MD
Qty: