Pumps Made Ready

Equipment Type Pressure Washer
Gallons Per Minute 3.0
PSI 2500
Weight 12 lbs
COMMERCIAL DUTY RADIAL-AXIAL PUMPS
Abrasion proof, heat resistant, industrial ceramic plungers
Stainless steel unitized check valves
Forged brass manifold
Industrial duty construction for extended life
Patent registered ball bearing design
Built-in garden hose adapter
Double sealing buna textile V-packing
Maximum Pump Speed: 3400 RPM
Shaft Size Hollow 3/4" ID
Type Hollow Shaft Pump

Equipment Type Pressure Washer
PSI 2500
Shaft Size 3/4"
Gallons Per Minute 2.5
Weight 7.5 lbs
Manifold: Aluminum prescision die cast special anticorrosion finish, brass and forged
Crankcase: Precision die cast, large coupling fins
Bearings: Premium oversized ball and needle bearings
Valves, Seats, and Springs: Plastic poppet seat and cage, stainless steel spring
Seals: Buna N-2000 double seals
2500 PSI maximum
140F maximum temperature
Oil capacity 3.5 oz
Flange width: 4-1/4"
Total Depth: 7"
Front width: 6-1/4"
Height: 5-5/8"
3400 RPM
Flange Gas Engine Flange
Inlet Female Garden Hose
Outlet 22mm/14mm Male (Accepts Female Screw Connect)
Includes Thermal Relief Valve
Built-In Pressure Control And Chemical Injector
Pump Is Prefilled With Oil
Type Axial Shafts Pump

Equipment Type Pressure Washer
PSI 2500
Shaft Size 3/4"
Gallons Per Minute 2.5
Weight 11 lbs
Inlet 1/2" MPT
Outlet 3/8" MPT
High strength forged brass manifold for long term use
Three 10mm grade 8.8 bolts
Ceramic coated stainless steel pistons for longer life in harsh environments
Angular contact ball bearings stabilizes the cranshaft and one thrust needle bearing absorbs the plunger load and assure long radial plate life. All are made of heat treated steel for extended life.
Stainless steel valves, seats, and springs with specially designed ultra form cages to provide extra long life and positive seating
Continuously lubricating seals and v-packings for extended life
Built-in unloader to optimize performance while reducing setup time. Integral trap pressure, fixed or adjustable chemical injector.
SPECIAL NOTE: Use synthetic oil only. (part#6601). DO NOT change oil. Ue oil only to add if low. This oil is specially formulated synthetic oil with special additives for the demands ov the XJ pump series. No other oil is factory approved for this pump, and could result in pump failure.
Maximum pump speed: 3400 RPM
Stroke: 5.8mm
Maximum fluid temperature: 140° F
Crancase oil capacity: 4.5 oz.
Bore .591" (15mm)
Type Axial Shafts Pump

Equipment Type Pressure Washer
PSI 2500
Gallons Per Minute 2.88
Inlet 3/8" FPT
Outlet 1/4" FPT
Easily replace your old pump with a pump made ready. Simply remove your old pump and slide this pmr onto the shaft of your gas engine. This pump made ready consists of the pump, a VB3K adjustable pressure actuated unloader with a thermal relief valve to help prevent overheating, along with an inlet filter. All fittings are quick connected.
IDEAL FOR ALL GENERAL CLEANING APPLICATIONS
Forged brass manifold with exclusive lifetime warranty
New, oversized connecting rods for ultimate crankcase performance
Die cast, anodized aluminum, oil bath crankcase
Solid ceramic plungers with continuously lubricated packings
The original interpump unitized, stainless steel, K123 inlet and outlet valves
SAE J609 gasoline engine mounting flange
Rated Pump Speed: 3400 RPM
Stroke: 6.6mm
Crankcase Oil Capacity: 11.0 oz.
Maximum Fluid Temperature: 165 F.
Weight 11.4 lbs
Bore .591" (15mm)
Unloader: VB3KTT
Size 7.0" x 7.2" x 5.5"
Shaft Size Hollow 3/4" ID
Flange Gas Engine Flange
Type Gas Flange Pump

Equipment Type Pressure Washer
PSI 2000
Gallons Per Minute 3.0
Weight 20 lbs
Inlet 1/2" FPT
Outlet 3/8" FPT
Easily replace your old pump with a pump made ready. Simply remove your old pump and slide this pmr onto the shaft of your gas engine. This pump made ready consists of the pump, a VR54 adjustable pressure actuated unloader with a thermal relief valve to help prevent overheating, along with an inlet filter. All fittings are quick connected.
Reversible crankshaft for easy right or left hand mounting
Forged bronze connecting rods with lifetime warranty
Hardened stainless steel piston guides
High efficiency stainless steel check valves
Abrasion proof, heat resistant, industrial ceramic plungers
High quality buna-textile double sealing v-packings
Design for optimal operating temperature
High quality oversized bearings
Die-cast anodized aluminum chrankshaft fin
Maximum Pump Speed: 3400 RPM
Minimum Horsepower Requirements: 6.0 hp for gas engines
Crankcae Capacity: 9.87 oz use SAE 20W/30 oil
Lubrication: fill crankcase with SAE 20W/30 oil per pump specifications. Change oil after initial 50 hour break-in period, then in 500 hour intervals thereafter.
Unloader: VR54
Built In Uniflow Unloader and Adjustable Chemical Injector
Pump Manufacturers Recommend Replacing Pump Crankcase Oil After An Initial 50 Hour Break In Period. Following the Intial Break In Period the Oil Should be Replaced Every 3 Months or 500 Hours Whichever Comed First. the Pump Oil Level Should Be Part of Your Daily Inspection.
Shaft Size Hollow 3/4" ID
Flange Gas Engine Flange
Gas Flange Pumps
Type Gas Flange Pump

Equipment Type Pressure Washer
PSI 3000
Gallons Per Minute 4.0
Weight 20 lbs
Inlet 1/2" FPT
Outlet 3/8" FPT
Bore .591" (15mm)
Size 8.8" x 9.7" x 6.5"
Unloader: VRT3-310EZ
Easily replace your old pump with a pump made ready. Simply remove your old pump and slide this pmr onto the shaft of your gas engine. This pump made ready consists of the pump, a VRT3-250 adjustable pressure actuated unloader with a thermal relief valve to help prevent overheating, along with an inlet filter. All fittings are quick connected.
Solid ceramic plungers
Standard SAE J609 gasoline mounting flange for up to 13 hp engines
Forged brass manifold with an exclusive lifetime warranty and 4:1 hydrostatic rating
Die cast, anodized aluminum, oil bath crankcase
Premium roller bearing
Unitized stainless steel inlet and discharge valves
Available in "L" left handed version
Direct Drive with Gas Flange
Maximum Inlet Pressure: 125 PSI
Stroke: .374" (9.5mm)
Crankcase Capacity: 14 oz. Nondetergent SAE 30W oil
Maximum Fluid Temperature: 165° F
Lubrication: Fill the crankcase to dot on oil gauge window per specifications with SAE 30W oil. Change the oil afte 40 hour break-in period, then every three (3) months or 500 hour intervals thereafter.
Flanged For Mounting on Up To 13 Horsepower Engines
Maximum Inlet Pressure 125 PSI
Shaft Size Hollow 1" ID
Flange Gas Engine Flange
Gas Flange Pumps

Equipment Type Pressure Washer
Gallons Per Minute 3.0
PSI 1500
Weight 14 lbs
Inlet 3/8" FPT
Outlet Dual 3/8" FPT
Bore .708" (18mm)
Size 9.13" x 6.65" x 6.50"
Easily replace your old pump with a pump made ready. Simply remove your old pump and slide this pmr onto the shaft of your electric motor. This pump made ready consists of the pump, a VRT3-160 adjustable pressure actuated unloader with a thermal relief valve to help prevent overheating, along with an inlet filter. All fittings are quick connected.
We have added some features to the standard 2SFX. these include an inlet fitting, and pressure relief valve.
UNIFLOW design provides continuous fluid flow forward through the pump, reduces cavitation risk and increases pump life
Unique spring loaded inlet valves and the flow through ceramic plungers allow excellent suction capabilities.
Ultimate portability, less than 11 pounds, less than 10" long.
Regulating unloader is standard on each pump to assure system pressure control and pump protection
Maximum Inlet Pressure: 75 PSI
Maximum Pump Speed: 3450 RPM
Minimum Horsepower Requirements: 3.0 bhp
Stroke: .177" (4.5mm)
Crankcase Capacity: 11.83 oz. use CAT Pump hydraulic oil
Maximum Fluid Temperature: 160 Degrees F.
By-pass Port: 1/4" FPT
Lubrication: fill crankcase with CAT Pump hydraulic oil per pump specifications. DO NOT RUN PUMP WITHOUT OIL IN CRANKCASE. Change initial oil after a 50 hour break-in period, and every three months or 500 hour intervals thereafter.
High Temp Pump
Unloader: 7500XS
Shaft Size Hollow 5/8" ID
Type Electric Flange Pump

Equipment Type Pressure Washer
PSI 3500
Gallons Per Minute 5.6
Weight 32 lbs
Inlet 1/2" FPT
Outlet 3/8" FPT
Bore .787" (20mm)
Size 12.2" x 9.2" x 6.9"
Unloader: VRT3-310EZ
Easily replace your old pump with a pump made ready. Simply remove your old pump and slide this pmr onto the shaft of your electric motor or gas engine. This pump made ready consists of the pump, a VRT3-310EZ adjustable pressure actuated unloader with a built-in easy start valve, athermal relief valve to help prevent overheating, along with an inlet filter. All fittings are quick connected.
Maximum Pump Speed: 1125/1450 RPM
Minimum Horsepower Requirements: 11.5 bhp (17.3 hp for gas engines)
Stroke: .630" (16mm)
Crankcase Capacity: 40.6 oz. Nondetergent SAE 30W oil
Maximum Fluid Temperature: 165° F
Lubrication: fill the crankcase to dot on oil gauge window per specifications with Nondetergent SAE 30W oil. Change oil after 40 hour break-in period, then every three (3) months or 500 hour intervals thereafter
Shaft Size .945" (24mm)
Type Solid Shaft Pump

Equipment Type Pressure Washer
PSI 2000
Gallons Per Minute 2.2
Weight 19 lbs
Easily replace your old pump with a pump made ready. Simply remove your old pump and slide this pmr onto the shaft of your electric motor. This pump made ready consists of the pump, a VRT3-160 adjustable pressure actuated unloader with a thermal relief valve to help prevent overheating, along with an inlet filter. All fittings are quick connected.
Reversible crankshaft for easy righ or left hand mounting
Forged bronze connecting rods with lifetime warranty
Hardened stainless steel piston guides
High efficiency stainless steel check valves
Abrasion proof, heat resistant, industrial ceramic plungers
High quality buna-textile double sealing v-packings
High quality oversized bearings
Design for optimal operating temperature
Die-cast anodized aluminum chrankshaft fin
LWS Series pumps feature anodized, die cast aluminum crankcase, solid ceramic plungers, stainless steel check valves and piston guides and BUNA-textile V-packings. They have a 5/8" hollow shaft with a NEMA 56C flange and a reversible crankcase for easy right hand or left hand mounting.
Maximum Pump Speed: 3400 RPM
Minimum Horsepower Requirements: 3.0 bhp
Crankcase Capacity: 11 oz. use SAE 20W/30 oil
Lubrication: fill crankcase with SAE 20W/30 oil per pump specifications. Change oil after initial 50 hour break-in period, then in 500 hour intervals thereafter
VRT3-160
Shaft Size Hollow 5/8" ID
Type Electric Flange Pump

Equipment Type Pressure Washer
PSI 3500
Gallons Per Minute 4.0
Weight 17.5 lbs
Inlet 1/2" FPT
Outlet 3/8" FPT
Bore .591" (15mm)
Easily replace your old pump with a pump made ready. Simply remove your old pump and slide this pmr onto the shaft of your gas engine. This pump made ready consists of the pump, a VRT3-310EZ adjustable pressure actuated unloader with a built-in easy start valve, a thermal relief valve to help prevent overheating, along with an inlet filter. All fittings are quick connected.
Increased fin depth increases surface area to maximize heat dissipation
Stainless steel unitized check valves
Heat resistant solid ceramic plungers operating on lubricated packings
Direct Drive mounting flange
Reinforced crankcase for increased load capacity
Enlarged crankcase increases oil capacity for better lubrication and lower operating temperatures
One piece industrial grade oversized bronze connecting rods
Maximum Pump Speed: 3400 RPM
Minimum Horsepower Requirements: 13 hp for gas engines
Crankcase Capacity: 14 oz. use SAE 20W/30 oil
Piston: 15mm
Unloader: VRT3-310EZ
Flange Gas Engine Flange
Your Unloader and Pressure Relief Valve May Need to Be Adjusted Prior to Useage
Shaft Size Hollow 1" ID
Flange Gas Engine Flange
Type Gas Flange Pump