Category: lawn-mowers

How to Install the Grass Bag for a Snapper P2185020

The following instructions are for the Snapper 21" Series 20 Steel Deck Walk Mower, which is for the model number P2185020. Before attempting to work on/with your equipment in any way, always refer to your owner's manual for safety information.

  1. Install the grass bag adapter.
  2. Install the grass bag by sliding the connector over the adapter flange.
  3. Attach the grass bag hooks over the middle handle cross bar.

For information about safety, warranty, and your specific model, read and be familiar with your owner's manual.

Related Products and Links

How to Adjust the Throttle Wire for a Husqvarna R120S

The following instructions are for the Husqvarna Rider, which is for the model number R120S. Before attempting to work on/with your equipment in any way, always refer to your owner's manual for safety information.

  1. Release the clamping screw that secures the wire casing ans set the choke control to maximum choke.
  2. Pull the choke wire casing to the far right and tighten the clamping screw.
  3. Pull back the throttle to the full throttle position and check that the choke is no longer actuated.

For information about safety, warranty, and your specific model, read and be familiar with your owner's manual.

Related Products and Links

How to Stop the Engine for a Husqvarna R120S

The following instructions are for the Husqvarna Rider, which is for the model number R120S. Before attempting to work on/with your equipment in any way, always refer to your owner's manual for safety information.

  1. Preferably allow the engine to idle for a minute to obtain normal working temperature before stopping it if it has been working hard.
  2. Lift up the cutting unit by pulling the lever backwards to its locked position.
  3. Pull back the throttle and let the motor idle for at least 30 seconds.
  4. Turn the ignition key to the "STOP".
  5. When the Rider is at a standstill, press down the parking brake and push in the locking button.

For information about safety, warranty, and your specific model, read and be familiar with your owner's manual.

Related Products and Links

How to Replace the Bearing on the Pulley End of the Hex Shaft for a Snapper P2185020

The following instructions are for the Snapper 21" Series 20 Steel Deck Walk Mower, which is for the model number P2185020. Before attempting to work on/with your equipment in any way, always refer to your owner's manual for safety information.

  1. Hold the hex shaft with an adjustable wrench held next to the pulley.
  2. Remove the 3/8" hex lock nut, located on the outside of the right wheel bracket.
  3. Remove the holder, O-ring, and bearing.
  4. Install the new bearing.
  5. Carefully install the new O-ring over the outside of the new bearing.
  6. Install the bearing holder, and secure with screws.
  7. Install the 3/8" hex lock nut.

For information about safety, warranty, and your specific model, read and be familiar with your owner's manual.

Related Products and Links

How to Replace the Transmission Poly-V Belt for a Snapper P2185020

The following instructions are for the Snapper 21" Series 20 Steel Deck Walk Mower, which is for the model number P2185020. Before attempting to work on/with your equipment in any way, always refer to your owner's manual for safety information.

  1. Remove the driven disc.
  2. Note the routing of the old belt around the three pulleys before removing it.
  3. Place the new Poly-V Belt over the end of the hex shaft and onto the drive pulley.
  4. Work the belt onto the top of the idler pulley.
  5. Twist the belt sideways and pull it upward between the differential bracket and driven pulley and then down into the pulley groove. Make sure the Poly-V Belt is above the belt guide.

For information about safety, warranty, and your specific model, read and be familiar with your owner's manual.

Related Products and Links