|


|
|
Part Number: 2177 |
|
Specs |
Temperature: 150° F Maximum
Inlet: 1/2" MPT
Gallons Per Minute: 10
Equipment Type: Pressure Washer
PSI: 1000-6000
Adjustable relief valve
The pressure relief valve is a safety device on the pressure washer. When a pre-determined pressure is reached within the system, the valve opens and releases water into the atmoshpere, or back into the line. The pressure relief valve is normally a second line of safety defense when used in conjunction with an unloader. It can also be used as the sole pressure safety device when installed in an open gun system.
PRESET AT 1000 PSI One model fits all pressures...no springs to change Less "whistling" and chatter than competing brands Highly accurate over full range of pressures Designed and made in the USA
|
Fits Model |
|
Replaces OEM |
Universal :
General Pump : 100729
|
|
|
|


|
|
Part Number: 2185 |
|
Specs |
Temperature: 150° F Maximum
Inlet: 1/2" MPT
Gallons Per Minute: 10
Outlet: Hose Barb
Equipment Type: Pressure Washer
PSI: 1000-6000
Adjustable relief valve
The pressure relief valve is a safety device on the pressure washer. When a pre-determined pressure is reached within the system, the valve opens and releases water into the atmoshpere, or back into the line. The pressure relief valve is normally a second line of safety defense when used in conjunction with an unloader. It can also be used as the sole pressure safety device when installed in an open gun system.
PRESET AT 1000 PSI One model fits all pressures...no springs to change Less "whistling" and chatter than competing brands Highly accurate over full range of pressures Designed and made in the USA
|
Fits Model |
|
Replaces OEM |
Universal :
General Pump : 100722 w/barb
|
|
|
|


|
|
Part Number: 2428 |
|
Specs |
Temperature: 50°- 400° F Maximum
Inlet: 1/4" MPT
Stem Diameter: 2 1/2"
Equipment Type: Pressure Washer
PSI: 3000
2" Face Plate
|
Fits Model |
|
Replaces OEM |
Universal :
|
|
|
|


|
|
Part Number: 2468 |
|
Specs |
Temperature: 140° F Maximum
Stem Diameter: 1/4" MPT Back Mount
Material: Stainless Steel
Equipment Type: Pressure Washer
PSI: 0-5000
2-1/2" Face
Glycerine Filled
|
Fits Model |
|
Replaces OEM |
Universal :
|
|
|
|


|
|
Part Number: 2426 |
|
Specs |
Temperature: 140° F Maximum
Stem Diameter: 1/4" MPT
Material: Stainless Steel
Equipment Type: Pressure Washer
PSI: 0-3000
2-1/2" Face
Glycerine Filled
|
Fits Model |
|
Replaces OEM |
Universal :
|
|
|
|


|
|
Part Number: 3885 |
|
Specs |
Equipment Type: Pressure Washer
Creates flow pulsations on demand to improve nozzle movement and cleaning power in sewer cleaning applications
Simple operation allows both full-flow and pulsation modes
Large, easy to grasp handle
Designed and made in the USA
Easy installation, replace middle inlet valve cap and valve
Turn a General Pump into a Sewer Jetting machine the inexpensive way!
|
Fits Model |
GENERAL PUMP : EZ2536E EZ2536S EZ2542E EZ2542S EZ2545E EZ2545S EZ2555E EZ2555S EZ3035G EZ3035S EZ3040G EZ3040S EZ3045G EZ3042S Pressure Washer
|
Replaces OEM |
General Pump : 100316
|
|
|
|


|
|
Part Number: 4766 |
|
Specs |
Equipment Type: Pressure Washer
Creates flow pulsations on demand to improve nozzle movement and cleaning power in sewer cleaning applications
Simple operation allows both full-flow and pulsation modes
Large, easy to grasp handle
Designed and made in the USA
Easy installation, replace middle inlet valve cap and valve
Turn a General Pump into a Sewer Jetting machine the inexpensive way!
|
Fits Model |
GENERAL PUMP : T9121 TS821 TS921 TS1021 T9131 TS1011 T1011 TS1331 TS1321 T9161 TS1621 T1621 TS1521 TS1711 T9211 TS1511 TS2011 T1511 T2011 TS2021 T9281 T5050 Pressure Washer
|
Replaces OEM |
General Pump : 100317
|
|
|
|


|
|
Part Number: 3486 |
|
Specs |
Temperature: 150° F Maximum
Gallons Per Minute: 10
Equipment Type: Pressure Washer
PSI: 1900-3500
Adjustable relief valve
The pressure relief valve with a hose barb is utilized mainly in low pressure systems in place of an unloader. In higher pressure systems, this pressure relief valve is used to return low pressure water to either the float tank or inlet side of the pump.
|
Fits Model |
|
Replaces OEM |
Universal :
|
|
|
|


|
|
Part Number: 3130 |
|
Specs |
Temperature: 150° F Maximum
Inlet: 3/8" MPT
Gallons Per Minute: 10
Equipment Type: Pressure Washer
PSI: 1900-3500
Adjustable relief valve
The pressure relief valve is a safety device on the pressure washer. When a pre-determined pressure is reached within the system, the valve opens and releases water into the atmoshpere, or back into the line. The pressure relief valve is normally a second line of safety defense when used in conjunction with an unloader. It can also be used as the sole pressure safety device when installed in an open gun system.
|
Fits Model |
|
Replaces OEM |
Universal :
|
|
|
|


|
|
Part Number: 2422 |
|
Specs |
Length: 6" Tube
Equipment Type: Pressure Washer
PSI: 0-300
Fuel pump pressure testing is simple with this adapted gauge. Simply screw the 6" tube with 1/8" nipple into fuel pump test port. Test from 0 to 300 PSI
|
Fits Model |
|
Replaces OEM |
Universal :
|
|
|
|


|
|
Part Number: 2407 |
|
Specs |
Note:: CAN BE SHIPPED VIA GROUND SERVICE ONLY
Temperature: 200° F Maximum
Inlet: 3/8" FPT
Gallons Per Minute: 12 GPM Maximum
Outlet: 3/8" FPT
Weight: 3 lbs
Capacity: 8-1/2 cu. Inches
Equipment Type: Pressure Washer
Burst Strength: 10,000 PSI minimum
Precharge Pressure: 1250 PSI maximum
Install on the inlet of pump to extend pump and system life by reducing pulsations. Accumulator is to be pre-charged with nitrolgen to one-half the system operating pressure. Do not pre-charge beyond the rated system operating pressure.It is recommended that the accumulator be mounted pointing down as a safety precaution. This procedure allows the accumulator to remain cooler during system operation and prolongs the effective operating life of the accumulator bladder. Shelf life of the nitrogen pre-charge of accumulator is approximately six months before re-charging is necessary. It is recommended the nitrogen pre-charge be checked approximately every three months after installation in a pressure system.
|
Fits Model |
GIANT PUMP : 220550A
|
Replaces OEM |
Universal :
Giant Pump :
|
|
|
|


|
|
Part Number: 1889 |
|
Specs |
Temperature: 150° F Maximum
Color: Orange
Inlet: 3/8" MPT
Gallons Per Minute: 10
Equipment Type: Pressure Washer
PSI: 2400-3600
Adjustable relief valve
The pressure relief valve is a safety device on the pressure washer. When a pre-determined pressure is reached within the system, the valve opens and releases water into the atmoshpere, or back into the line. The pressure relief valve is normally a second line of safety defense when used in conjunction with an unloader. It can also be used as the sole pressure safety device when installed in an open gun system.
PRESET AT 1000 PSI One model fits all pressures...no springs to change Less "whistling" and chatter than competing brands Highly accurate over full range of pressures Designed and made in the USA
|
Fits Model |
|
Replaces OEM |
Universal :
Giant Pump :
|
|
|
|


|
|
Part Number: 2323 |
|
Specs |
Temperature: 150° F Maximum
Color: Blue
Inlet: 3/8" MPT
Gallons Per Minute: 10
Equipment Type: Pressure Washer
PSI: 3600-5000
Adjustable relief valve
The pressure relief valve is a safety device on the pressure washer. When a pre-determined pressure is reached within the system, the valve opens and releases water into the atmoshpere, or back into the line. The pressure relief valve is normally a second line of safety defense when used in conjunction with an unloader. It can also be used as the sole pressure safety device when installed in an open gun system.
PRESET AT 1000 PSI One model fits all pressures...no springs to change Less "whistling" and chatter than competing brands Highly accurate over full range of pressures Designed and made in the USA
|
Fits Model |
|
Replaces OEM |
Universal :
General Pump :
|
|
|
|


|
|
Part Number: 3597 |
|
Specs |
Temperature: 145° F Maximum
Inlet: 1/4" MPT
Weight: 1.5 oz
Equipment Type: Pressure Washer
PSI: 100
Hose barb: 90 1/4"
Protects the pump from damaging heat build up while it is in bypass mode. The thermal relief valve, sensing a rise in temperature opens and discharges a small amount of heated fluid. This allows cooler water to enter the system and cool the pump. When the gun is discharged the cooler water will cause the valve to close immediately.
Most consistent temperature range on the market Quickest response to rising temperature Less stress on the pump Shorter overall length Most cost effective thermal protector on the market Mounts easily in the pump manifold, inlet water supply or bypass loop plumbing.
|
Fits Model |
|
Replaces OEM |
Universal :
General Pump : 100557
|
|
|
|


|
|
Part Number: 3980 |
|
Specs |
Size: 20mm
Equipment Type: Pressure Washer
|
Fits Model |
GENERAL PUMP : CW2004, CW2040, CW3040
|
Replaces OEM |
General Pump :
|
|
|
|


|
|
Part Number: 3509 |
|
Specs |
Temperature: 400° F Maximum
Inlet: 3/8" Quick Connect for Easy Testing
Equipment Type: Pressure Washer
PSI: 3000
Test pump pressure up to 5000 PSI, and water temperature to 400°F. 3/8" quick connects for easy testing.
|
Fits Model |
|
Replaces OEM |
Universal :
|
|
|
|


|
|
Part Number: 758539 |
|
Specs |
Pounds Per Square Inch: Pressures to 5,000
Equipment Type: Pressure Washer
Glycerin filled
Stainless steel case and rim
1/4" NPT
|
Fits Model |
|
Replaces OEM |
Universal :
General Pump : 320003
|
|
|
|


|
|
Part Number: 758811 |
|
Specs |
Temperature: 140° F.
Inlet: 3/8" MALE THREAD (NPT)
Equipment Type: Pressure Washer
|
Fits Model |
|
Replaces OEM |
General Pump : 100557
|
|
|
|


|
|
Part Number: 758619 |
|
Specs |
Temperature: 140° F.
Inlet: 1/2" MALE THREAD (NPT)
Equipment Type: Pressure Washer
|
Fits Model |
|
Replaces OEM |
General Pump : 100558
|
|
|
|


|
|
Part Number: 3375 |
|
Specs |
Size: 24mm x 1-1/8"
Material: Heavy duty cast aluminum flange
Equipment Type: Pressure Washer
Self-aligning resilient coupling
Compact design
Quiet maintenance free drive system
Fits 3 to 5 HP motors Fits 184TC frame
|
Fits Model |
|
Replaces OEM |
Universal :
General Pump : ZG184TC
|
|
|
|